SAFETY
Product certified by independent technical inspection: Type 2 of the standard ISO 6185.
This product is not intended for use by children under 12 years of age.
Teenagers from 13 to 17 years old must only use this product under the direct supervision of an adult.
Always wear a life jacket.
Refer to the local regulations and information about the dangers of float tubes and navigation.
Maximum load: 130 kg
Maximum motor power: 300 Watts
PRE-EQUIPPED FOR THE FLTB MTR MOTOR
The FLTB-5 V2 is pre-equipped to easily add the FLTB MTR motor (8666881 not included)
The motor can be quickly and easily clipped onto the base under the seat.
The cable guide behind the backrest enables you to easily connect the motor to the battery (not included), which must be stored in a watertight storage bag at the rear. (8606699 not included)
You now just have to position the control unit within reach.
COMPATIBLE ACCESSORIES
The following compatible accessories will make your fishing outings more comfortable: (not included)
8606699 FLTB REAR STORAGE BAG: trapezoidal rear storage bag to increase your storage capacity
8737484 FLTB KPN: floating keepnet to keep your catch
8560032 FLTB SDC: rod rack to transport your 4 rigs in complete safety
8560034 FLTB SES: depth sounder support to easily install your electronics
INFLATION AND INSTALLATION
Lay the float tube out on a clean, flat surface.
Inflate the seat, then the side air chambers to 1.5 PSI/0.1 bar to avoid any risk of over-inflation and/or explosion.
We recommend using the pump FLTB PLP 10 PSI (ref: 8643922), which is equipped with a pressure gauge to guarantee accurate inflation.
Once sitting, install the apron.
DEFLATION AND STORAGE
To deflate the float tube, unscrew the valves with caution.
Fold the left side of the float tube over onto the seat, then repeat with the right side.
Take hold of the tip, and fold it down over the length of the seat.
Do the same with the ends of the two side float chambers.
Insert the float tube into the bag.
Once dry, your FLTB-5 can be stored folded inside the carry bag.
You will extend its lifetime by storing it flat and slightly inflated.
DIMENSIONS AND WEIGHT
FLOAT TUBE FLTB-5 V2: 115 x 145 cm (width x length)
Diameter of the side air chambers 35 cm
Dimensions of the inflated seat: 46 x 40 cm (width x depth)
Dimensions when folded in the carry bag: 75 x 43.5 x 10 cm
Weight: 6.2 kg (without the storage bags and the carry bag)
STORAGE BAG 500 S / Volume: 4 L
Dimensions: 21.5 x 14.5 x 11 cm
STORAGE BAG 500 M / Volume: 6 L
Dimensions: 25 x 22 x 12 cm
STORAGE BAG 500 L / Volume: 10 L
Dimensions: 39.5 x 23.5 x 12 cm
EQUIPMENT
The bag contains:
- Float tube with 4 valves and bladders positioned in the compartments
- Deck base and its measurement gauge (up to 60 cm)
- Built-in side rod holder (1 rod)
- 3 bakkan bags for storing accessories (see dimensions below)
- Ventilated transport bag
- User guide + user manual
- Repair kit without glue
Main section: P600 and PVC tarpaulin (0.45 mm)
Air chambers: PVC (0.45 mm)
Storage bags: PVC
SPARE PARTS
The following parts are available on this web site or in our stores (to order):
8754652 SEAT AIR CHAMBER FLTB-5
8754650 BACKREST AIR CHAMBER FLTB-5
8552350 RIGHT AIR CHAMBER FLTB-5
8552351 LEFT AIR CHAMBER FLTB-5
8649864 MINI BOSTON VALVE (backrest and seat air chambers)
8649866 or 8187669 or 8338891 BOSTON VALVE (side air chambers)
8842490 APRON CONNECTOR FLTB-5 V2
8512384 REPAIR KIT
Warranty
2 years (stitched and bonded parts)
The warranty does not cover punctured air chambers.
